Hirdetés
- droidic: Windows 11 önállóság nélküli világ: a kontroll új korszaka
- sziku69: Fűzzük össze a szavakat :)
- Geri Bátyó: Agglegénykonyha 9 – Az impulzusvásárlás is lehet tudatos
- sidi: 386-os Chicony gázplazma laptop memóriabővítése
- D1Rect: Nagy "hülyétkapokazapróktól" topik
- Luck Dragon: Asszociációs játék. :)
- eBay-es kütyük kis pénzért
- Brogyi: CTEK akkumulátor töltő és másolatai
- ubyegon2: Airfryer XL XXL forrólevegős sütő gyakorlati tanácsok, ötletek, receptek
- Real Racing 3 - Freemium csoda
-
LOGOUT
Amit érdemes tudni a Raspberry Pi-kről:
A legelső változat 2012-ben jelent meg. Pici, olcsó és nagyon alacsony fogyasztású, hobby-célú kártyagép. Felépítése ARM alapú, nem PC-architektúra, hanem kb. egy régi mobilhoz hasonló. Nagyon sok mindenre használható! A Linux-nak és a magas eladási mennyiségnek köszönhetően jelentős fejlesztőtáborral rendelkezik.
Új hozzászólás Aktív témák
-
Plehboj
tag
válasz
JoceeHunt
#40741
üzenetére
Nem működő reboot problémára (USB-és segédtáp/tápos hub használata esetén jön elő rpi4-en) találtam egy hozzászólást egy fórumon.
Tudna valaki - aki ért mélyebben az elektronikához - segíteni abban, hogy pontosan mit és hogyan kellene bütykölni ehhez ?Itt a leírás hozzá:
I tried first using a schottkey diode between the power to the hub and the hub but this didn't help. I decided to see what happened with the red removed altogether. This still didn't help either.
I can't recall all the details off the top of my head but part of how USB works involves the hub pulling up USB data lines at times and it seems this is either enough to allow a voltage to then leak back to the power rails the RPi PMIC is checking, or that the problem is in fact slightly different and somehow caused by the presence of a USB hub at boot confusing the bootloader. In either case the solution I came up with was a simple modification to the hub using a few bits out the parts bin and 10 minutes with the soldering iron. I found* an NPN transistor,
* a P channel MOSFET (grossly over-rated at 61 Amps, but that's what I had to hand) and
* a couple of 4k7 resistors.The VBus signal (red wire) from the host connects to the base of the transistor via a 4k7 resistor. The Emitter is connected to GND (black wire from host). The Source of the FET connects to the external power source in (which is isolated from the hub), and the Drain to the hubs power rail. The collector of the transistor is connected to the gate of the FET such that it is pulled down when the host provides power, thus switching on the FET and powering the hub. The remaining 4k7 resistor between the Power source and the gate prevents it floating around. Finally I put the Schottky diode back in place such that the hub can still be used without external power.
My rpi4 now boots perfectly every time (from LAN) and with a USB DVD drive connected, something the previous rpi3 wouldn't do.
Új hozzászólás Aktív témák
- Asztali PC v5 , R5 8400F , RX 5700 XT , 16GB DDR5 , 512GB NVME , 500GB HDD
- Intel Core i9-9900K, Gigabyte Z390 AORUS Master, Noctua NH-D15
- Ryzen 7 kezdő 1080p játszós konfig
- BESZÁMÍTÁS! ASUS B660M i5 12400F 16GB DDR4 1TB SSD RTX 3070 8GB Zalman T4 Plus Cooler Master 750W
- BESZÁMÍTÁS! Asrock B450M R7 3800X 16GB DDR4 512GB SSD RX 6600XT 8GB GameMax STORM Black Adata 600W
- ÚJ akku! Lenovo ThinkPad X1 Extreme Gen2 i7-9850H 16GB 512GB GTX1650 500nit UHD 1 év teljeskörű gar.
- HP EliteBook 850 G7 15.6 inch (256GB SSD, i5-10310U, 1.70GHz, 8GB DDR4) Sale.exe: Akció!
- AMD AM4-es HP OMEN 25L GT12 alaplapok - B550 chipset
- Xiaomi Redmi Note 12S 256GB, Kártyafüggetlen, 1 Év Garanciaval
- Xiaomi Watch S4, 1 Év Garanciával
Állásajánlatok
Cég: NetGo.hu Kft.
Város: Gödöllő
Cég: PCMENTOR SZERVIZ KFT.
Város: Budapest
wassermann
