SATA22pin - USB3.0 adapter
--------------------------
Model: WLX-889U3
Csatlakozó: SATA 22pin (adat+táp)
Csatlakozó: USB 3.0
DC 12V tápbemenet

- HW: JMicron JMS539S
- VID: 152D, PID: 2339
- Tray ikon: USB Mass Storage
- Eszközkezelő: <HDD> USB Device
- Leválasztás: Nem áll le.
- Inaktivitás: Nem áll le.
- HDD Sentinel: Nem támogatja!

CrystalDiskMark: Win sem látja!

dmesg:

[ +0.979437] usb 3-4: new high-speed USB device number 49 using xhci_hcd
[ +0.165218] usb 3-4: New USB device found, idVendor=152d, idProduct=2339
[ +0.000012] usb 3-4: New USB device strings: Mfr=10, Product=11, SerialNumber=3
[ +0.000003] usb 3-4: Product: USB Mass Storage
[ +0.000002] usb 3-4: Manufacturer: WANLONGXIN
[ +0.000002] usb 3-4: SerialNumber: 000000000041
[ +0.000613] usb-storage 3-4:1.0: USB Mass Storage device detected
[ +0.000101] scsi55 : usb-storage 3-4:1.0
[ +1.002411] scsi 55:0:0:0: Direct-Access HTS72108 0G9SA00 0000 PQ: 0 ANSI: 2 CCS
[ +0.000276] sd 55:0:0:0: Attached scsi generic sg3 type 0
[ +0.000222] sd 55:0:0:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ +0.000440] sd 55:0:0:0: [sdc] Write Protect is off
[ +0.000005] sd 55:0:0:0: [sdc] Mode Sense: 28 00 00 00
[ +0.000385] sd 55:0:0:0: [sdc] No Caching mode page found
[ +0.000004] sd 55:0:0:0: [sdc] Assuming drive cache: write through
[ +0.121620] usb 3-4: USB disconnect, device number 49
[ +0.005694] sd 55:0:0:0: [sdc] Unhandled error code
[ +0.000005] sd 55:0:0:0: [sdc]
[ +0.000002] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ +0.000002] sd 55:0:0:0: [sdc] CDB:
[ +0.000002] Read(10): 28 00 00 00 00 00 00 00 08 00
[ +0.000009] end_request: I/O error, dev sdc, sector 0
[ +0.000003] Buffer I/O error on device sdc, logical block 0
[ +0.000032] ldm_validate_partition_table(): Disk read failed.
[ +0.000042] sdc: unable to read partition table
[ +0.000170] sd 55:0:0:0: [sdc] READ CAPACITY failed
[ +0.000003] sd 55:0:0:0: [sdc]
[ +0.000002] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ +0.000002] sd 55:0:0:0: [sdc] Sense not available.
[ +0.000022] sd 55:0:0:0: [sdc] Attached SCSI disk
[ +0.975488] usb 3-4: new high-speed USB device number 50 using xhci_hcd
sesame:~ #

- hdparm 9.4.3: Linuxon IO hibák miatt nem működik!
- smartctl 6.3: Linuxon IO hibák miatt nem működik!
- hddtemp 0.3-beta15: Linuxban IO hibák miatt nem működik!
- GSmartControl 0.8.7: Linuxon IO hibák miatt nem működik!

Konklúzió:
2.5" SATA eszközökhöz külső táp nélkül lenne használható.
3.5" SATA eszközökhöz külső 12V táppal lenne használható.
De egy kalap ürülék!
Az adatkapcsolati hibák miatt teljesen használhatatlan!
Az alap firmware-rel, USB2.0-es eszközként ismeri fel az OS, dmesg-ben "high-speed USB device".