Sziasztok!

Van egy sok éves merevlemezem (WDC_WD3000HLFS-01G6U0 WD-WXLY08150646) és azt kérdezném meg a szakértőktől, hogy az alább hosszú szöveg pontosan mit jelent (tökéletes most a merevlemez, vagy sem)?
A válaszokat előre is köszönöm!

KissA

smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.4.2-pmagic64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital VelociRaptor
Device Model: WDC WD3000HLFS-01G6U0
Serial Number: WD-WXLY08150646
LU WWN Device Id: 5 0014ee 05693bb6c
Firmware Version: 04.04V01
User Capacity: 300,069,052,416 bytes [300 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 10000 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Wed Apr 13 05:23:07 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x05) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 199 197 021 Pre-fail Always - 3033
4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6046
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 041 041 000 Old_age Always - 43718
10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 6005
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 1187
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6050
194 Temperature_Celsius 0x0022 110 099 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 2
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 62 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 62 occurred at disk power-on lifetime: 43282 hours (1803 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 db 70 40 Error: UNC at LBA = 0x0070db00 = 7396096

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 00 2b 8a 07 08 00:09:22.952 READ FPDMA QUEUED
60 00 08 00 2b 8a 07 08 00:09:22.952 READ FPDMA QUEUED
60 00 e0 00 27 8a 07 08 00:09:22.950 READ FPDMA QUEUED
60 00 d0 00 25 8a 07 08 00:09:22.949 READ FPDMA QUEUED
60 00 18 00 69 f7 06 08 00:08:42.923 READ FPDMA QUEUED

Error 61 occurred at disk power-on lifetime: 40207 hours (1675 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 80 ad 15 55 e0 Error: UNC 128 sectors at LBA = 0x005515ad = 5576109

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 80 20 16 4d 01 08 00:00:29.996 READ DMA EXT
25 00 20 a0 2c 62 01 08 00:00:29.967 READ DMA EXT
ec 00 00 00 00 00 00 08 00:00:29.939 IDENTIFY DEVICE
35 00 01 e8 71 4a 01 08 00:00:29.807 WRITE DMA EXT
25 00 01 e8 71 4a 01 08 00:00:29.802 READ DMA EXT

Error 60 occurred at disk power-on lifetime: 38793 hours (1616 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 00 70 c9 72 40 Error: IDNF at LBA = 0x0072c970 = 7522672

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 88 d8 8f a0 02 08 01:16:55.176 WRITE FPDMA QUEUED
61 00 78 10 ee 3a 03 08 01:16:55.173 WRITE FPDMA QUEUED
61 00 78 10 ee 3a 03 08 01:16:55.173 WRITE FPDMA QUEUED
61 00 78 10 ee 3a 03 08 01:16:55.172 WRITE FPDMA QUEUED
61 00 78 10 ee 3a 03 08 01:16:55.172 WRITE FPDMA QUEUED

Error 59 occurred at disk power-on lifetime: 38682 hours (1611 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a0 98 9e 40 Error: UNC at LBA = 0x009e98a0 = 10393760

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 80 50 20 99 9e 00 08 00:25:39.333 READ FPDMA QUEUED
60 80 50 20 99 9e 00 08 00:25:39.333 READ FPDMA QUEUED
60 58 40 e8 8b 9e 00 08 00:25:39.328 READ FPDMA QUEUED
60 50 38 98 8b 9e 00 08 00:25:39.328 READ FPDMA QUEUED
60 08 c0 f0 6d 6c 00 08 00:25:39.320 READ FPDMA QUEUED

Error 58 occurred at disk power-on lifetime: 38612 hours (1608 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 00 a0 98 6b 40 Error: IDNF at LBA = 0x006b98a0 = 7051424

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 20 90 a0 98 6b 00 08 05:45:08.388 WRITE FPDMA QUEUED
61 0b 88 b3 11 6e 00 08 05:45:08.387 WRITE FPDMA QUEUED
61 02 78 b1 11 6e 00 08 05:45:08.386 WRITE FPDMA QUEUED
61 10 70 98 98 6b 00 08 05:45:08.385 WRITE FPDMA QUEUED
61 06 68 ab 11 6e 00 08 05:45:08.385 WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 43715 -
# 2 Extended offline Completed without error 00% 43715 -
# 3 Extended offline Interrupted (host reset) 10% 43713 -
# 4 Conveyance offline Completed without error 00% 43712 -
# 5 Short offline Completed without error 00% 43712 -
# 6 Conveyance offline Interrupted (host reset) 70% 43711 -
# 7 Conveyance offline Interrupted (host reset) 80% 43711 -
# 8 Conveyance offline Interrupted (host reset) 90% 43711 -
# 9 Extended offline Interrupted (host reset) 90% 43711 -
#10 Short offline Completed without error 00% 43709 -
#11 Conveyance offline Completed without error 00% 43599 -
#12 Conveyance offline Interrupted (host reset) 90% 43596 -
#13 Extended offline Aborted by host 90% 38060 -
#14 Extended offline Completed without error 00% 38056 -
#15 Short offline Completed without error 00% 38055 -
#16 Extended offline Aborted by host 90% 30790 -
#17 Conveyance offline Completed without error 00% 30705 -
#18 Short offline Completed without error 00% 30583 -
#19 Extended offline Completed without error 00% 13537 -
#20 Extended offline Aborted by host 90% 13536 -
#21 Short offline Completed without error 00% 8090 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.