Új hozzászólás Aktív témák

• #353 biomika csendes tag

  Új Válasz 2011-03-01 19:50:39 #353

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  biomika

  csendes tag

  Sziaszok,
  az én dsl321b modememben W25X16VSSIG-es FLASH van, attól h a chip nevének vége nem egyezik, még mehet rá a firmware?
  köszi elöre is!

  # dmesg
  Linux version 2.6.8.1 (root@BB3) (gcc version 3.4.2) #1 Thu Oct 22 09:42:16 CST 2009
  Serial flash device: name W25X16VSSIG, id 0xef14, size 2048KB
  96332CG prom init
  CPU revision is: 00029010
  Determined physical RAM map:
  memory: 007a0000 @ 00000000 (usable)
  On node 0 totalpages: 1952
  DMA zone: 1952 pages, LIFO batch:1
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
  Built 1 zonelists
  Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
  brcm mips: enabling icache and dcache...
  Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
  Primary data cache 8kB 2-way, linesize 16 bytes.
  PID hash table entries: 32 (order 5: 256 bytes)
  Using 120.000 MHz high precision timer.
  Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
  Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
  Memory: 6048k/7808k available (1261k kernel code, 1740k reserved, 187k data, 64k init, 0k highmem)
  Calibrating delay loop... 239.20 BogoMIPS
  Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
  Checking for 'wait' instruction... unavailable.
  NET: Registered protocol family 16
  Total Flash size: 2048K with 512 sectors
  File system address: 0xbfc10100
  Can't analyze prologue code at 80149dd4
  PPP generic driver version 2.4.2
  NET: Registered protocol family 24
  Using noop io scheduler
  bcm963xx_mtd driver v1.0
  brcmboard: brcm_board_init entry

  ======= GPIO CONFIG_BCM96338 inited ========
  Serial: BCM63XX driver $Revision: 3.00 $
  ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
  NET: Registered protocol family 2
  IP: routing cache hash table of 512 buckets, 4Kbytes
  TCP: Hash tables configured (established 512 bind 1024)
  NET: Registered protocol family 1
  NET: Registered protocol family 17
  Ebtables v2.0 registered
  NET: Registered protocol family 8
  NET: Registered protocol family 20
  VFS: Mounted root (squashfs filesystem) readonly.
  Freeing unused kernel memory: 64k freed
  Algorithmics/MIPS FPU Emulator v1.5
  atmapi: module license 'Proprietary' taints kernel.
  adsl: adsl_init entry
  blaadd: blaa_detect entry
  Broadcom BCMPROCFS v1.0 initialized
  Broadcom BCM6338A2 Ethernet Network Device v0.3 Oct 22 2009 09:41:13
  Config Internal PHY Through MDIO
  BCM63xx_ENET: 100 MB Full-Duplex (auto-neg)
  eth0: MAC Address: F0:7D:689:17:23
  eth0 Link UP.
  ZIPB............
  FLAG: 1
  BcmAdsl_Initialize=0xC00683C8, g_pFnNotifyCallback=0xC0081004
  AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003980 adsl2=0x00000000
  pSdramPHY=0xA07FFFF8, 0x1B78DA 0xDEADBEEF
  AdslCoreHwReset: AdslOemDataAddr = 0xA07F9244
  AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003980 adsl2=0x00000000
  dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
  ATM proc init !!!
  ZIPB............
  FLAG: 1
  Device UP br0
  Fib_add_ifaddr : DEV br0
  Device UP: br0
  Device add to fib: br0
  device eth0 entered promiscuous mode
  br0: port 1(eth0) entering learning state
  br0: topology change detected, propagating
  br0: port 1(eth0) entering forwarding state
  ADSL G.994 training
  device nas_0_1_32 entered promiscuous mode
  br0: port 2(nas_0_1_32) entering learning state
  br0: topology change detected, propagating
  br0: port 2(nas_0_1_32) entering forwarding state
  eth0 Link DOWN.
  eth0 Link UP.

  ioctl, p_name=diapd
  ADSL G.992 started
  ADSL G.992 channel analysis
  ADSL G.992 message exchange
  ADSL link down
  ADSL G.994 training
  ADSL G.992 started
  ADSL G.992 channel analysis
  ADSL G.992 message exchange
  ADSL link up, interleaved, us=1085, ds=17330
  ATM Soft SAR: ATM link connected.
  eth0 Link DOWN.
  br0: port 1(eth0) entering disabled state
  eth0 Link UP.
  br0: port 1(eth0) entering learning state
  br0: topology change detected, propagating
  br0: port 1(eth0) entering forwarding state
  eth0 Link DOWN.
  br0: port 1(eth0) entering disabled state
  eth0 Link UP.
  br0: port 1(eth0) entering learning state
  br0: topology change detected, propagating
  br0: port 1(eth0) entering forwarding state
  eth0 Link DOWN.
  br0: port 1(eth0) entering disabled state
  eth0 Link UP.
  br0: port 1(eth0) entering learning state
  br0: topology change detected, propagating
  br0: port 1(eth0) entering forwarding state
  #

Új hozzászólás Aktív témák