Amit érdemes tudni a Raspberry Pi-kről:
A legelső változat 2012-ben jelent meg. Pici, olcsó és nagyon alacsony fogyasztású, hobby-célú kártyagép. Felépítése ARM alapú, nem PC-architektúra, hanem kb. egy régi mobilhoz hasonló. Nagyon sok mindenre használható! A Linux-nak és a magas eladási mennyiségnek köszönhetően jelentős fejlesztőtáborral rendelkezik.
Gyorskeresés
Legfrissebb anyagok
Általános témák
LOGOUT.hu témák
- [Re:] [D1Rect:] Nagy "hülyétkapokazapróktól" topik
- [Re:] Elektromos rásegítésű kerékpárok
- [Re:] Android másképp: Lineage OS és társai
- [Re:] [attilasd:] A laposföld elmebaj: Vissza a jövőbe!
- [Re:] [gban:] Ingyen kellene, de tegnapra
- [Re:] [TheLázs:] ADHS
- [Re:] [Sub-ZeRo:] Euro Truck Simulator 2 & American Truck Simulator 1 (esetleg 2 majd, ha lesz) :)
- [Re:] eBay-es kütyük kis pénzért
- [Re:] [sziku69:] Fűzzük össze a szavakat :)
- [Re:] [sziku69:] Szólánc.
Szakmai témák
PROHARDVER! témák
Mobilarena témák
IT café témák
Téma összefoglaló
- Utoljára frissítve: 2023-08-02 12:58:01
LOGOUT.hu
Hozzászólások
Norbika88
senior tag
For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
0# uncomment if you get no picture on HDMI for a default "safe" mode
hdmi_safe=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
overscan_left=24
overscan_right=24
overscan_top=24
overscan_bottom=24
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
hdmi_ignore_edid=0xa5000080
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=4
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Disable compensation for displays with overscan
disable_overscan=0
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[all]
[pi4]
# Run as fast as firmware / board allows
arm_boost=1
Nincs ötletem, lehet megdöglött a hdmi rajta...
Mai Hardverapró hirdetések
prémium kategóriában
- Lenovo Thinkpad P70 " szép állapot "
- MacBook Pro (15", 2019 Mid)
- Lenovo ThinkPad T470s, I7-6600U, 8GB RAM, FHD, 2 év garancia, áfás számla! (41)
- DELL 7070 SFF Core i7 8700 vagy i7 9700 8/16GB DDR4 250GB M.2 SSD számla + gari - több db
- Lenovo ThinkPad T470s, I5-7300U, 16GB RAM, FHD, 2 év garancia, áfás számla! (39)