- lezso6: Nem látszik a kurzor Chrome alatt a beviteli mezőkben?
- vrob: Az IBM PC és a játékok a 80-as években
- eBay-es kütyük kis pénzért
- hdanesz: Elektromos autózás - első élmények
- D1Rect: Nagy "hülyétkapokazapróktól" topik
- Luck Dragon: Asszociációs játék. :)
- Lalikiraly: SÜNI energiaital.
- zebra_hun: Hűthető e kulturáltan a Raptor Lake léghűtővel a kánikulában?
- Gurulunk, WAZE?!
- sziku69: Fűzzük össze a szavakat :)
-
LOGOUT
Arduino hardverrel és szoftverrel foglakozó téma. Minden mikrovezérlő ami arduinoval programozható, és minden arduino program, board, és hardverrel kapcsolatos kérdések helye.
Új hozzászólás Aktív témák
-
válasz
gya/352 #19457 üzenetére
esptool.py -p com4 erase_flash
Ezzel is próbáld meg, ahogy a linkelt oldalon írják.
Próbáltál már különböző memória kiosztásokat (APP/OTA/SPIFFS) beállítani feltöltés előtt?
Az oldalon egyébként írják az okokat is:
SOLVED:
We are now 99% sure this problem is actually caused by a hardware design issue with our USB programming board.
During the condition where the main power supply to the board is OFF but the programmer is still connected to USB, we see stray voltages on the pins connected to the ESP32, including the MTDI pin. This pin has an internal pull down in the ESP, but it is not active until after power is applied. Where it has floated high during power down, it looks like the pin is not pulled low fast enough at power on, and gets read as "1". This causes the VDD_SDIO to be set to 1.8v instead of 3.3v. We observe that the pin strapping shown by the bootloader is 0x33 or 0x3f instead of 0x13. The condition persists a software reboot, and our testers were usually experiencing a recurrence of the problem if they cycled the power. However, reprogramming the board would reset it until some future power interruption caused it to recur.
The problem did not happen on our original boards because the flash still worked correctly even at the lower voltage. However, more recent boards have a later ESP module with a different flash chip (Manufacturer: c8; Device: 4017). I have now confirmed that on these boards, the flash can be read but cannot be written when VDD_SDIO has been set to 1.8v.
I have worked around the problem on our dev boards by running this espefuse command to set the VDD_SDIO to 3.3v via the e-fuses:
CODE:python path\to\esp\tools\espefuse.py -p comX set_flash_voltage 3.3V
Van neked kötve valami az MTDI pin-re (GPIO12)? Ha jól értem egy külső lehúzó ellenállás (pl 10kΩ) esetleg megoldhatja a dolgot.
Új hozzászólás Aktív témák
Hirdetés
- Milyen billentyűzetet vegyek?
- AMD Ryzen 9 / 7 / 5 9***(X) "Zen 5" (AM5)
- Autós topik látogatók beszélgetős, offolós topikja
- Hónap végén érkezik a Xiaomi Band 10, ára is van
- Nyaralás előtti hardverszemle
- Samsung Galaxy A52s 5G - jó S-tehetség
- Filmvilág
- AliExpress tapasztalatok
- Motoros topic
- Lítium-ion/Li-ion akkumulátorok
- További aktív témák...
- UF Lenovo Yoga 9i x360 Érintős Hajtogatós Laptop Tab 14" -60% i7-1360P 16/1TB Iris Xe 2,8K OLED 90Hz
- Lenovo Yoga 9i x360 Érintős Hajtogatós Laptop Tab 14" -60% i7-1260P 16/512 Iris Xe 2,8K OLED 90Hz
- Új DELL Inspiron 16 Fémházas Multimédiás Laptop 16" -40% Ryzen 7 8840U 8mag 16/1TB FHD+ IPS
- Új DELL Inspiron 16 Fémházas Multimédiás Laptop 16" -40% Ryzen 7 8840U 8mag 16/1TB FHD+ IPS
- Sony FE 28-70 mm F3.5-5.6 OSS
- LG 27CN650N-6A - Felhő Monitor - 1920x1080 FHD - 75Hz 5ms - USB Type-C - Quad Core - BT + WiFi
- Tablet felvásárlás!! Apple iPad, iPad Mini, iPad Air, iPad Pro
- Csere-Beszámítás! Asus Prime RTX 5060Ti 16GB GDDR7 Videokártya! Bemutató darab!
- Telefon felvásárlás!! Samsung Galaxy A50/Samsung Galaxy A51/Samsung Galaxy A52/Samsung Galaxy A53
- Samsung Galaxy A22 5G 128GB, Kártyafüggetlen, 1 Év Garanciával
Állásajánlatok
Cég: Liszt Ferenc Zeneművészeti Egyetem
Város: Budapest
Cég: CAMERA-PRO Hungary Kft
Város: Budapest