Hirdetés

Keresés

Új hozzászólás Aktív témák

  • Router

    őstag

    válasz Hunter2 #16214 üzenetére

    Én monitorból kukáztam FFC LVDS kábelt, az pont jó méret. Egyelőre a billentyűzetes cucc szerintem nem fog menni mert laponként változik a lábkiosztás.

    Kaptál az RT809-hez ISP adaptert, arról kell lehúznod a CS, CLK, DIN, DO lábakat a megfelelő helyre, a billentyűzet csatira, illetve a gnd-t de nálam a tápot is az íróról kellett adni mert a lap saját táplálásával hibát dobott állandóan. Viszont ha nem akarsz madzagolni akkor legegyszerűbb levenni az EC-t és mergírni az adapterrel utána pedig vissza.

    Az ajándék dvd-ket pedig nyugodtan akaszd fel a visszapillantóra, másra nem jók. Szedd le a legfrissebb szoftvert a géphez (nálam 20160329) ez már látja a KB9012-9016 kontrollereket is.

  • Router

    őstag

    válasz Hunter2 #16214 üzenetére

    Én monitorból kukáztam FFC LVDS kábelt, az pont jó méret. Egyelőre a billentyűzetes cucc szerintem nem fog menni mert laponként változik a lábkiosztás.

    Kaptál az RT809-hez ISP adaptert, arról kell lehúznod a CS, CLK, DIN, DO lábakat a megfelelő helyre, a billentyűzet csatira, illetve a gnd-t de nálam a tápot is az íróról kellett adni mert a lap saját táplálásával hibát dobott állandóan. Viszont ha nem akarsz madzagolni akkor legegyszerűbb levenni az EC-t és mergírni az adapterrel utána pedig vissza.

  • kris54

    csendes tag

    válasz Hunter2 #16214 üzenetére

    Nem tudom talán segíthet
    Please USE TNM keyboard adaptor.
    Connect laptop Keyboard flat cable to 32 pin connector of adaptor.
    If flat cable has less than 32 pins ,align Flat pin1 to connector pin 1.
    Connect ISP /JTAG pin 10 of TNM (rear 10 pin connector of TNM5000) to
    the GND of motherboard with a short and thick wire (for example motherboard USB GND)
    Press "Config" button ,set ITE Keyboard connector functions from laptop Schematic.
    or load laptop fuse files from "Fuse List File" menu.
    Power On the motherboard. then read or program.
    Program button will erase + Program+verify the chip , no need for further verify.

    many motherboard files can be found at web address:
    "http://www.tnmelectronics.com/downloads/ITE-keymapConfigTNM.rar"
    User Guide can be found at web address:
    "http://www.tnmelectronics.com/downloads/ITE-ENE-HelpE.pdf"

    Note: If chip has bad firmware or is blank , ISP woudn't work.
    in this case you may need desoldering & programming on TNM ITE-8xxx Adpator.

    If you haven't this adaptor, Use the following map for connection of 24-32 pin flat cable :
    Motheborad GND -> TNM ISP Pin10
    Please connect Motherboard Keyboard Connector in series with 100 ohm resistors to TNM ZIF:
    Keyboard pin1 -> TNM ZIF pin2
    Keyboard pin2 -> TNM ZIF pin47
    Keyboard pin3 -> TNM ZIF pin3
    Keyboard pin4 -> TNM ZIF pin46
    Keyboard pin5 -> TNM ZIF pin4
    Keyboard pin6 -> TNM ZIF pin45
    Keyboard pin7 -> TNM ZIF pin5
    Keyboard pin8 -> TNM ZIF pin44
    Keyboard pin9 -> TNM ZIF pin6
    Keyboard pin10 -> TNM ZIF pin43
    Keyboard pin11 -> TNM ZIF pin7
    Keyboard pin12 -> TNM ZIF pin42
    Keyboard pin13 -> TNM ZIF pin8
    Keyboard pin14 -> TNM ZIF pin41
    Keyboard pin15 -> TNM ZIF pin9
    Keyboard pin16 -> TNM ZIF pin40
    Keyboard pin17 -> TNM ZIF pin10
    Keyboard pin18 -> TNM ZIF pin39
    Keyboard pin19 -> TNM ZIF pin11
    Keyboard pin20 -> TNM ZIF pin38
    Keyboard pin21 -> TNM ZIF pin12
    Keyboard pin22 -> TNM ZIF pin37
    Keyboard pin23 -> TNM ZIF pin13
    Keyboard pin24 -> TNM ZIF pin36
    Keyboard pin25 -> TNM ZIF pin14
    Keyboard pin26 -> TNM ZIF pin35
    Keyboard pin27 -> TNM ZIF pin15
    Keyboard pin28 -> TNM ZIF pin34
    Keyboard pin29 -> TNM ZIF pin16
    Keyboard pin30 -> TNM ZIF pin33
    Keyboard pin31 -> TNM ZIF pin17
    Keyboard pin32 -> TNM ZIF pin32

Új hozzászólás Aktív témák