Új hozzászólás Aktív témák

• #2728 Xpod addikt

  Új Válasz 2009-01-02 17:55:13 #2728

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  Xpod

  addikt

  Remélem ezzek segítenek.

  At ifconfig kiemente:

  eth1 Link encap:Ethernet HWaddr 00:14:A5:66:3B:F9
  UP BROADCAST MULTICAST MTU:1500 Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:2492 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1000
  RX bytes:0 (0.0 b) TX bytes:104664 (102.2 KiB)
  Interrupt:11 Base address:0xc000

  A dmesg kimente. (rövidítve)

  bcm43xx: Chip ID 0x4318, rev 0x2
  bcm43xx: Number of cores: 4
  bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
  bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
  bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
  bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
  bcm43xx: PHY connected
  bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
  bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
  bcm43xx: Radio turned off
  bcm43xx: Radio turned off
  .
  .
  .
  bcm43xx: PHY connected
  bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
  bcm43xx: Radio turned on
  bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm4 3xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
  bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm4 3xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
  bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm4 3xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
  bcm43xx: Chip initialized
  bcm43xx: 32-bit DMA initialized
  bcm43xx: Keys cleared
  bcm43xx: Selected 802.11 core (phytype 2)
  bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm4 3xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
  bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
  bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
  bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
  bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
  lp: driver loaded but no devices found

  Kiadtam csak simán az iwconfig eth1 parancsot.
  ESSID: off/any
  Mode: Merged
  Access Point: invalid
  Link quality: 0
  Signal level: 0
  Noise level: 0
  Encription key: off

Új hozzászólás Aktív témák